Expert Answers about Holiday Rambler Vacationer Motorhome
- Motor Upgrade Kit For A 1999 Holiday Rambler Vacationer With Lippert 32 Series Steps
- Yes!
The Motor Upgrade Kit for Kwikee Electric RV Steps # LC379145 is everything you need for your 1999 Holiday Rambler with the Lippert 32 series steps.
The motor included in this kit has 40% more torque than your OEM motor, and includes screws, washers, and nuts for installation.
view full answer... - 72" x 75" Short King RV Mattress for a Holiday Rambler Motorhome
- We have a few options that are 72" wide and 75" long. I have listed them for you below so you can take a look and decide what style is best for you.
- etrailer eDream RV Mattress # e64FR (inner spring)
- etrailer eDream Supreme RV Mattress # e67FR (hybrid)
- etrailer eDream Deluxe RV Mattress # e57FR (pocket coil)
- Denver Mattress Luxe 2 Hybrid RV Mattress # DE27RR (hybrid)
view full answer... - Tie Rod Orientation for Installing Roadmaster Reflex # RM-RBK22-RSSA on Ford F-53
- We've had this question come up before and here's what Roadmaster sent me in response:
The axle bracket can be located on either the driver or passenger side and the tie rod bracket (B802) can be located on top or bottom side of the tie rod.
Orientation of the shock is not important, the unit can have the spring pointed towards the center of the RV or out towards the tire. Similarly, the eyelets on the shock unit (where bolts hold it to the brackets) can be located on both the top or...
view full answer... - Replacement Step Control Module for 2011 HR Vacationer
- Yes it does sound like the control module of your Lippert RV steps is having issues which is causing the problem you are having and the replacement would then be the part # LC301702 that you referenced.
view full answer... - Replacement Gearbox for Kwikee Steps With 676062 Motor
- Before you replace anything make sure the linkage is still attached with the cotter pin. If it is not, reattaching the linkage will likely solve your problem. Assuming it is still attached, the tension has been lost within the linkage and gearbox assembly, and you will need to replace it with the Replacement Gear Box and A Linkage # LC379160.
It is perfectly acceptable to replace just the gearbox if the motor is functioning. However, if you need to replace the 676062 motor it is only...
view full answer... - Slide Slickers to Protect RV Carpet
- The only slide slickers we carry are the Lippert Carpet Protectors for RVs with Slide Outs # LC134993 which measure 40" long x 5" wide. This will be a standard size and should be able to fit a wide variety of slide out sizes.
view full answer... - Availability of 3/4 inch Wide 100 foot Long Vinyl Trim for RV
- We have a 100 foot roll of 3/4 inch wide RV Vinyl Insert Trim part # CAM25262 which I believe is what you are looking for. For black you'd want the part # CAM25272, for beige part # CAM25252 or for cream part # CAM25242.
view full answer... - Steering Stabilizer For 2008 Holiday Rambler Coach with Roadmaster Chassis With Leaf Springs
- I was able to confirm that the steering stabilizer you need for your 2008 Holiday Rambler motorhome with Roadmaster chassis with leaf springs is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK8-RSSA. I confirmed the fit with Roadmaster Inc.
They don't have any Anti-Sway Bars compatible with your chassis at this time.
view full answer... - Will Tekonsha Prodigy P2 Trailer Brake Controller Work With 2024 Tiffin Allegro Bay 38BB
- Yes, the Tekonsha Prodigy P2 # 90885 will work with your 2024 Tiffin Allegro Bay 38BB. A brake controller like this will work with any motorhome or vehicle that has a 7-way installed. There is no custom wiring harness available so you will have to splice the wires for installation.
view full answer... - Replacement Inner and Complete Arm Assemblies for Roadmaster BlackHawk 2 All-Terrain Tow Bars
- Yes, the Replacement Inner Arm Assembly # RM-910021-75 is the correct replacement arm for your Roadmaster BlackHawk 2 All Terrain, Non-Binding Tow Bar # RM-422 with serial number 018660.
We also have the Drivers Side Arm # RM-910021-95 and Passenger Side Arm # RM-910021-97 if you need to replace the entire arm assembly on either side.
view full answer... - Coach Steps Chattering While Retracted
- I spoke with my contact at Lippert about the issue you are having with your Coach Steps. They stated that this is likely a result of the motor not "amping out" rather than a faulty control module. When the step is fully retracted, the motor should send out a high amperage rating to the control module which it then recognizes as the step being fully retracted and cuts power. The motor is likely not reaching the "amping out" figure so the control module doesn't know when to cut power.
The...
view full answer... - Steering Stabilizer for 2019 Holiday Rambler Vacationer 35P
- Yes, since your 2019 Holiday Rambler Vacationer 35P is built on the Ford F-53 chassis and it has a GVWR of 24,000 pounds the Roadmaster Reflex Steering Stabilizer # RM-RBK25-RSSA you referenced is the correct kit and it will work perfectly. This will do a great job of keeping the RV in line during travel by mounting between the steering mechanism and chassis and constantly working to maintain its position.
All the custom mounting brackets are included. I have attached a short video demonstration...
view full answer... - Wiring Multiple Heater Pads to an On/Off Switch
- For starters, I have attached a photo of how the Universal-Design Rocker Switch part # PK34360 should be wired. However, I believe the issue you are having is in regards to the size of wire used. The correct size or (gauge) will vary depending on factors such as amp draw and length of wire.
The wires running from the heater to the splice can be anywhere from 16 gauge - 10 gauge depending on length. However, once the three heater wires are spliced together and traveling to the switch you...
view full answer... - Replacement Mattress For A 2018 Holiday Rambler Vacationer 35P
- According to the floor plan, for options 113, 131, 208, 833, for your 2018 Holiday Rambler Vacationer 35P, then you have a King Eurotop measuring 72" x 75".
With that information, the etrailer eDream RV Mattress # e64FR is the correct size replacement for your Rambler.
view full answer... - Can I Dolly Tow a 2019 Ford Edge SEL with FWD
- Yes. According to my research, the FWD models of the 2019 Ford Edge SEL should be towed using a dolly; I would recommend checking your vehicle's owner's manual to confirm this information. The Demco Kar Kaddy SS Tow Dolly # DM9713045 is the perfect solution to accomplish this as long as the distance between the outside tire treads on your vehicle is less than 76".
On top of the hydraulic disc brakes that make this tow dolly a great choice, the EZ latch surge coupler eliminates the need...
view full answer... - How Thick Is The Denver Mattress Supreme Euro Top RV Mattress # DE48ZR
- The Denver Mattress Supreme Euro Top RV Mattress - 80" Long x 76" Wide - King # DE48ZR is 11" in height.
view full answer... - How To Prevent Sway On a 2020 Holiday Rambler Vacationer (Ford - 26,000 GVWR)
- The best options we have to fight off sway on your 2020 Holiday Rambler Vacationer (Ford - 26,000 GVWR) are an anti rear sway bar followed by jounce spring upgrades. The combination of these parts will help drastically with sway, body roll, and overall stability/handling. If you were only to do one, I recommend the rear anti-sway as you will see the biggest improvement from this alone.
Roadmaster Rear Anti-Sway Bar part # RM-1139-149
SumoSprings Rebel Custom Helper Springs part # SSF-173-40-2
SumoSprings...
view full answer... - Correct Steering Stabilizer for a 2017 Holiday Rambler Vacationer 35P
- The 2017 Holiday Rambler Vacationer 35P is on a Ford F-53 chassis which I believe you alluded to therefore the correct Roadmaster Reflex Steering Stabilizer for you is part # RM-RBK22-RSSA. I have attached an install video of the stabilizer installed on a similar motorhome with the same chassis for you as well.
view full answer... - What Size Bolt Does the Replacement Jam Nut # WM9072F Fit
- The Replacement Jam Nut # WM9072F that you referenced does look similar to the jam nuts that you are currently using to secure your Wheel Masters cover. To determine if they will fit your application though you need to measure your bolt size.
This jam nut has 32 mm dimensions so your bolt needs to match for a fit. If you happen to have the 19F0J wheel liners then you need part # WM9073 instead.
view full answer...
Go To Results